True/False
Indicate whether the sentence or statement is true
or false.
|
|
|
1.
|
It is safe to run
the drill press at high speeds for any size drill bit.
|
|
|
2.
|
Inset
cabinet doors are mounted so they are flush with the face frame of the cabinet.
|
|
|
3.
|
You
should wait until the blade has completely stopped spinning before removing any small scraps for near
the blade.
|
|
|
4.
|
A
convenient work center has limited space around appliances.
|
|
|
5.
|
The operator
should stand directly in front of the saw blade while operating the table saw.
|
|
|
6.
|
The chuck key must
be removed from the chuck before turning the drill press on.
|
|
|
7.
|
The
top rail of a kitchen base cabinet is wider to allow for the shadow cast by the overhanging
countertop.
|
|
|
8.
|
Once
you find one stud on each wall, locate the others by measuring 16 inches left and
right.
|
|
|
9.
|
A
traditional style cabinet has a face frame covering the edges of the plywood carcass.
|
|
|
10.
|
Leveling legs are used on kitchen cabinets because they look really
cool.
|
|
|
11.
|
Work
surfaces refer to countertops or tabletop areas where certain tasks are performed.
|
|
|
12.
|
You must wear eye
protection when operating the table saw.
|
Multiple Choice
Identify the
letter of the choice that best completes the statement or answers the question.
|
|
|
13.
|
What
is the overall depth of a typical kitchen base cabinet
|
|
|
14.
|
The
typical overall depth of a kitchen wall cabinet is
|
|
|
15.
|
When
fastening wall cabinets to wall studs it is important to make sure the screw goes through
the a. | stud | c. | hanging
rail | b. | back of the
cabinets | d. | face
frame | | | | |
|
|
|
16.
|
When
drilling long pieces, the long end should be on the ________ side of the drill
press. a. | left | d. | backing
board | b. | right | e. | chuck key | c. | slower | | | | |
|
|
|
17.
|
The
finished height to the top of the countertop in a kitchen is
|
|
|
18.
|
Cabinets must be mounted a. | plumb | c. | to wall studs | b. | square | d. | All of the
above | | | | |
|
|
|
19.
|
The
installed height to the bottom of a wall cabinet in a kitchen is
|
Completion
Complete each sentence or
statement.
|
|
|
20.
|
In
this shop we use the radial arm saw to ________________ only.
|
Matching
|
|
|
Match
the following definitions to the correct term: a. | the pattern of line in cut lumber formed by the annual
rings | f. | when two lines
never intersect | b. | cutting with the grain of the
wood | g. | when two lines
are at a 90 degree angle | c. | cutting across the grain of the
wood | h. | the void that is
left by the saw blade | d. | the size of the stock needed before
maching | i. | dimension always
with the grain | e. | the exact size of the stock needed to complete the
project | j. | dimension always
across the grain | | | | |
|
|
|
21.
|
width
|
|
|
22.
|
grain
|
|
|
23.
|
kerf
|
|
|
24.
|
ripping
|
|
|
25.
|
crosscutting
|
|
|
26.
|
parallel
|
|
|
27.
|
finished dimensions
|
|
|
28.
|
length
|
|
|
29.
|
perpendicular
|
|
|
30.
|
rough
dimensions
|